The Notebooks of Leonardo Da Vinci - Complete

by Leonardo da Vinci

Available in 350 free installments

Owner:

View book

Email address:

Enter your email address above to start receiving your free daily installments.

Dripread will never disclose your email address to third parties.

Observe in alloying how many hours are wanted for each hundredweight. [In casting each one keep the furnace and its fire well stopped up.] [Let the inside of all the moulds be wetted with linseed oil or oil of turpentine, and then take a handful of powdered borax and Greek pitch with aqua vitae, and pitch the mould over outside so that being under ground the damp may not [damage it?]

[To manage the large mould make a model of the small mould, make a small room in proportion.]

[Make the vents in the mould while it is on the horse.]

Hold the hoofs in the tongs, and cast them with fish glue. Weigh the parts of the mould and the quantity of metal it will take to fill them, and give so much to the furnace that it may afford to each part its amount of metal; and this you may know by weighing the clay of each part of the mould to which the quantity in the furnace must correspond. And this is done in order that the furnace for the legs when filled may not have to furnish metal from the legs to help out the head, which would be impossible. [Cast at the same casting as the horse the little door]

[Footnote: The importance of the notes included under this number is not diminished by the fact that they have been lightly crossed out with red chalk. Possibly they were the first scheme for some fuller observations which no longer exist; or perhaps they were crossed out when Leonardo found himself obliged to give up the idea of casting the equestrian statue. In the original the first two sketches are above l. 1, and the third below l. 9.]

711.

THE MOULD FOR THE HORSE.

Make the horse on legs of iron, strong and well set on a good foundation; then grease it and cover it with a coating, leaving each coat to dry thoroughly layer by layer; and this will thicken it by the breadth of three fingers. Now fix and bind it with iron as may be necessary. Moreover take off the mould and then make the thickness. Then fill the mould by degrees and make it good throughout; encircle and bind it with its irons and bake it inside where it has to touch the bronze.

OF MAKING THE MOULD IN PIECES.

Draw upon the horse, when finished, all the pieces of the mould with which you wish to cover the horse, and in laying on the clay cut it in every piece, so that when the mould is finished you can take it off, and then recompose it in its former position with its joins, by the countersigns.

The square blocks a b will be between the cover and the core, that is in the hollow where the melted bronze is to be; and these square blocks of bronze will support the intervals between the mould and the cover at an equal distance, and for this reason these squares are of great importance.

The clay should be mixed with sand.

Take wax, to return [what is not used] and to pay for what is used.

Dry it in layers.

Make the outside mould of plaster, to save time in drying and the expense in wood; and with this plaster enclose the irons [props] both outside and inside to a thickness of two fingers; make terra cotta. And this mould can be made in one day; half a boat load of plaster will serve you.

Good.

Dam it up again with glue and clay, or white of egg, and bricks and rubbish.

[Footnote: See Pl. LXXV. The figure "40," close to the sketch in the middle of the page between lines 16 and 17 has been added by a collector's hand.

In the original, below line 21, a square piece of the page has been cut out about 9 centimetres by 7 and a blank piece has been gummed into the place.

Lines 22-24 are written on the margin. l. 27 and 28 are close to the second marginal sketch. l. 42 is a note written above the third marginal sketch and on the back of this sheet is the text given as No. 642. Compare also No. 802.]

712.

All the heads of the large nails.

[Footnote: See Pl. LXXVI, No. i. This drawing has already been published in the "Saggio delle Opere di L. da Vinci." Milano 1872, Pl. XXIV, No. i. But, for various reasons I cannot regard the editor's suggestions as satisfactory. He says: "Veggonsi le armature di legname colle quali forse venne sostenuto il modello, quando per le nozze di Bianca Maria Sforza con Massimiliano imperatore, esso fu collocato sotto un arco trionfale davanti al Castello."

713.

These bindings go inside.

714.